Differences
This shows you the differences between two versions of the page.
Both sides previous revision Previous revision | |||
rrdglcdadapter [2017/01/26 00:11] arthur |
rrdglcdadapter [2017/05/27 12:10] (current) arthur |
||
---|---|---|---|
Line 1: | Line 1: | ||
- | ++ RRD GLCD Adpater board | + | == RRD GLCD Adpater board |
This adapter allows you to connect a [[http://smoothieware.org/panel|Reprapdiscound GLCD panel]] to a Smoothieboard easily. | This adapter allows you to connect a [[http://smoothieware.org/panel|Reprapdiscound GLCD panel]] to a Smoothieboard easily. | ||
- | {{:rrdglcdadpapter/glcdav2.jpg|}} | + | {{:rrdglcdadapter:glcdav2.jpg?400|}} |
- | All of the panel's functionalities are available :Â | + | All of the panel's functionalities are available : |
* Display | * Display | ||
Line 29: | Line 29: | ||
== Assembly | == Assembly | ||
- | [[image glcdav2_kit.jpg]] | + | {{:rrdglcdadapter:glcdav2_kit.jpg?400|}} |
place the 3-pin connectors below the pcb | place the 3-pin connectors below the pcb | ||
- | [[image glcdav2_weld0.jpg]] | + | |
+ | {{:rrdglcdadapter:glcdav2_weld0.jpg?400|}} | ||
and solder | and solder | ||
- | [[image glcdav2_weld1.jpg]] | + | |
+ | {{:rrdglcdadapter:glcdav2_weld1.jpg?400|}} | ||
Mount the exp1 & exp2 connectors, and solder | Mount the exp1 & exp2 connectors, and solder | ||
- | [[image glcdav2_orig.jpg]][[image rrdglcdvo.png]] | + | |
+ | {{:rrdglcdadapter:glcdav2_orig.jpg?400|}} | ||
+ | |||
+ | {{:rrdglcdadapter:rrdglcdvo.png?400|}} | ||
on some rrdglcd the connector are reversed | on some rrdglcd the connector are reversed | ||
- | [[image glcdav2_copy.jpg]][[image rrdglcdcopy.png]] | + | |
+ | {{:rrdglcdadapter:glcdav2_copy.jpg?400|}} | ||
+ | |||
+ | {{:rrdglcdadapter:rrdglcdcopy.png?400|}} | ||
== Power supply | == Power supply | ||
If smoothieboard has good 5v regulator, or a 5V power supply, the panel of the power supply can be drawn from this one by means of a diode (ex 1N5817). | If smoothieboard has good 5v regulator, or a 5V power supply, the panel of the power supply can be drawn from this one by means of a diode (ex 1N5817). | ||
- | [[image glcdav2_power1.jpg]] | + | |
+ | {{:rrdglcdadapter:glcdav2_power1.jpg?400|}} | ||
if not, please install a voltage regulator Recom 785.0-1 | if not, please install a voltage regulator Recom 785.0-1 | ||
- | [[image glcdav2_power2.jpg]] | + | |
+ | {{:rrdglcdadapter:glcdav2_power2.jpg?400|}} | ||
the diode and regulator may be mounted at the same time | the diode and regulator may be mounted at the same time | ||
Line 50: | Line 66: | ||
for v1.0 smoothieboard, configure the PCB | for v1.0 smoothieboard, configure the PCB | ||
- | [[image glcdav2_config1.jpg]][[image glcdav2_config2.jpg]] | + | |
+ | {{:rrdglcdadapter:glcdav2_config1.jpg?400|}} | ||
+ | |||
+ | {{:rrdglcdadapter:glcdav2_config2.jpg?400|}} | ||
cut the jumper track, and drop a welding goute on the other part of the jumper | cut the jumper track, and drop a welding goute on the other part of the jumper | ||
Line 56: | Line 76: | ||
solder the connector missing | solder the connector missing | ||
- | [[image glcdv2_smoothie.png]] | + | {{:rrdglcdadapter:glcdv2_smoothie.png?400|}} |
Update firmware (version after october 2014), see [[Flashing Smoothie firmware]] | Update firmware (version after october 2014), see [[Flashing Smoothie firmware]] | ||
- | edit the config file on the µSD | + | edit the config file on the µSD |
<code> | <code> | ||
# config settings | # config settings | ||
Line 85: | Line 106: | ||
This will create a pseudo-switch that does nothing, but it will enable the pull-down on the pin. You have to leave out the panel.buzz_pin line. | This will create a pseudo-switch that does nothing, but it will enable the pull-down on the pin. You have to leave out the panel.buzz_pin line. | ||
- | connect exp1 & exp2, and plug on the smotthieboard | + | {{:rrdglcdadapter:adapter.jpg?400|}} |
- | + | ||
- | == Adapter v1 | + | |
- | + | ||
- | [[image adapter.jpg]] | + | |
The V1 of this adapter was not capable of accessing the panel's SDÂ card slot. | The V1 of this adapter was not capable of accessing the panel's SDÂ card slot. | ||
Line 95: | Line 112: | ||
This functionality can be made available on the v1 by cutting track on pcb | This functionality can be made available on the v1 by cutting track on pcb | ||
- | [[image gcldv1_03.jpg]] | + | {{:rrdglcdadapter:gcldv1_03.jpg?400|}} |
And soldering a cable under the pcb | And soldering a cable under the pcb | ||
- | [[image gcldv1_04.jpg]] | + | {{:rrdglcdadapter:gcldv1_04.jpg?400|}} |
+ | |||
+ |