Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
extruder-options [2018/08/17 10:31]
78.174.146.205
extruder-options [2019/12/20 14:09]
wolfmanjm
Line 1: Line 1:
-|| extruder.[[module_name]].enable || false || Whether to activate the extruder module at all. All configuration is ignored if false. Each time an <​kbd>​extruder.[[module_name]].enable</​kbd>​ line is encountered,​ an extruder module with the name «[[module_name]]» will be created. || +|| extruder.[[module_name]].enable || true || Whether to activate the extruder module at all. All configuration is ignored if false. Each time an <​kbd>​extruder.[[module_name]].enable</​kbd>​ line is encountered,​ an extruder module with the name «[[module_name]]» will be created. || 
 || extruder.[[module_name]].steps_per_mm || 140 || Steps/​millimetre for the extruder stepper motor. This is the number of steps to move one millimetre of filament. [[http://​smoothieware.org/​extruder#​steps_per_millimeter|Learn more]] ||  || extruder.[[module_name]].steps_per_mm || 140 || Steps/​millimetre for the extruder stepper motor. This is the number of steps to move one millimetre of filament. [[http://​smoothieware.org/​extruder#​steps_per_millimeter|Learn more]] || 
 || extruder.[[module_name]].filament_diameter || 1.74 || Filament diameter, in millimetres,​ used for volumetric extrusion control. [[http://​smoothieware.org/​extruder#​filament-diameter|Learn more]] || || extruder.[[module_name]].filament_diameter || 1.74 || Filament diameter, in millimetres,​ used for volumetric extrusion control. [[http://​smoothieware.org/​extruder#​filament-diameter|Learn more]] ||
Line 8: Line 8:
 || extruder.[[module_name]].dir_pin || <​kbd>​0.22</​kbd>​ || Pin for extruder stepper motor driver'​s direction signal ||  || extruder.[[module_name]].dir_pin || <​kbd>​0.22</​kbd>​ || Pin for extruder stepper motor driver'​s direction signal || 
 || extruder.[[module_name]].en_pin || <​kbd>​0.21</​kbd>​ || Pin for extruder stepper motor driver'​s enable signal ||  || extruder.[[module_name]].en_pin || <​kbd>​0.21</​kbd>​ || Pin for extruder stepper motor driver'​s enable signal || 
-|| extruder.[[module_name]].x_offset || 0 || Extruder offset from origin in millimetres for the X axis. This is useful ​when you have multiple extruders to specify the offset from each extruder to the first one. ||  +|| extruder.[[module_name]].x_offset || 0 || Extruder offset from origin in millimetres for the X axis. ONLY used when you have multiple extruders to specify the offset from each extruder to the first one. ||  
-|| extruder.[[module_name]].y_offset || 0 ||  Extruder offset from origin in millimetres for the Y axis. ||  +|| extruder.[[module_name]].y_offset || 0 ||  Extruder offset from origin in millimetres for the Y axis. ONLY used for multiple extruders ​||  
-|| extruder.[[module_name]].z_offset || 0 ||  Extruder offset from origin in millimetres for the Z axis. || +|| extruder.[[module_name]].z_offset || 0 ||  Extruder offset from origin in millimetres for the Z axis. ONLY used for multiple extruders ​|| 
 || extruder.[[module_name]].retract_length || 3 || Retract length in millimetres. Retract is a retractation of the filament called using the <​kbd>​G10</​kbd>​ G-code. It is recovered ( reverted ) using the <​kbd>​G11</​kbd>​ G-code. [[http://​smoothieware.org/​extruder#​retract|Learn more about retractation]] ​ ||  || extruder.[[module_name]].retract_length || 3 || Retract length in millimetres. Retract is a retractation of the filament called using the <​kbd>​G10</​kbd>​ G-code. It is recovered ( reverted ) using the <​kbd>​G11</​kbd>​ G-code. [[http://​smoothieware.org/​extruder#​retract|Learn more about retractation]] ​ || 
 || extruder.[[module_name]].retract_feedrate || 45 || Retract feed-rate ( filament speed ) in millimetres/​second ||  || extruder.[[module_name]].retract_feedrate || 45 || Retract feed-rate ( filament speed ) in millimetres/​second ||