Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
zprobe [2018/09/26 12:49]
93.236.64.159 typos
zprobe [2019/02/16 04:06] (current)
220.237.116.205 Replaced some pronouns with explicit references for clarity.
Line 86: Line 86:
 <​kbd>​G30 Fxxx</​kbd>​ will run the probe at xxx mm/min overriding the slow_feedrate. <​kbd>​G30 Fxxx</​kbd>​ will run the probe at xxx mm/min overriding the slow_feedrate.
  
-<​kbd>​G38.2</​kbd>​ and <​kbd>​G38.3</​kbd>​ ( for probing in X and Y ) are also implemented as documented [[http://​linuxcnc.org/​docs/​2.6/​html/​gcode/​gcode.html#​sec:​G38-probe|here]] ​+<​kbd>​G38.2</​kbd>​ and <​kbd>​G38.3</​kbd>​ ( for probing in X and Y ) are also implemented as documented [[http://​linuxcnc.org/​docs/​2.6/​html/​gcode/​gcode.html#​sec:​G38-probe|here]] ​**NOTE** probing in X or Y on a delta is not recommended due to non linear movement issues.
  
 If there are multiple levelling strategies selected the <​kbd>​Pn</​kbd>​ parameter will select which one to send leveling codes to, 0 being the first defined one, 1 the second and so on. eg <​kbd>​G29 P1</​kbd>​ will send G29 to the second defined levelling strategy. If there are multiple levelling strategies selected the <​kbd>​Pn</​kbd>​ parameter will select which one to send leveling codes to, 0 being the first defined one, 1 the second and so on. eg <​kbd>​G29 P1</​kbd>​ will send G29 to the second defined levelling strategy.
Line 461: Line 461:
 </​code>​ </​code>​
  
-Or they may be defined (and saved with <​kbd>​M500</​kbd>​) using <​kbd>​M557 P0 X30 Y40.5</​kbd> ​ where <​kbd>​P</​kbd>​ is <​kbd>​0,​1,​2</​kbd>​+Or the probe points ​may be defined (and saved with <​kbd>​M500</​kbd>​) using <​kbd>​M557 P0 X30 Y40.5</​kbd> ​ where <​kbd>​P</​kbd>​ is <​kbd>​0,​1,​2</​kbd>​
  
 Probe offsets from the nozzle or tool head can be defined with : Probe offsets from the nozzle or tool head can be defined with :
Line 469: Line 469:
 </​code>​ </​code>​
  
-They may also be set with <​kbd>​M565 X0 Y0 Z0</​kbd>​+The probe offsets ​may also be set with <​kbd>​M565 X0 Y0 Z0</​kbd>​
  
-To force homing in X and Y before <​kbd>​G32</​kbd>​ does the probe the following can be set in configthis is the default+To force homing in X and Y before <​kbd>​G32</​kbd>​ does the probethe following can be set in config ​(this is the default)
  
 <​code>​ <​code>​
Line 759: Line 759:
  
 <callout type="​default"​ icon="​true"​ title="​Going further">​ <callout type="​default"​ icon="​true"​ title="​Going further">​
-If you want to learn more about this module, or are curious how it works, Smoothie is Open-Source and you can simply go look at the code, [[https://​github.com/​Smoothieware/​Smoothieware/​blob/​edge/​src/​modules/​tools/​zprobe|here]].+If you want to learn more about this module, or are curious ​about how it works, Smoothie is Open-Source and you can simply go look at the code, [[https://​github.com/​Smoothieware/​Smoothieware/​blob/​edge/​src/​modules/​tools/​zprobe|here]].
 </​callout>​ </​callout>​