Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
supported-g-codes [2020/07/13 17:06]
arthur
supported-g-codes [2020/07/13 17:07] (current)
arthur
Line 38: Line 38:
 | G32 | Depends on levelling strategy selected, see [[ZProbe]]. For calibration on delta, uses Z probe to calibrate delta endstops and arm radius, use R parameter to select only arm radius calibration and E to select only endstop calibration. I to set target precision, J to set probe_radius,​ K to keep current endstop trim settings. ​ In Zgrid module, it starts the grid probing | <​kbd>​G32</​kbd>​ <​kbd>​G32 R</​kbd>​ <​kbd>​G32 E</​kbd>​ <​kbd>​G32 EK</​kbd>​ <​kbd>​G32 I0.02</​kbd>​ | | G32 | Depends on levelling strategy selected, see [[ZProbe]]. For calibration on delta, uses Z probe to calibrate delta endstops and arm radius, use R parameter to select only arm radius calibration and E to select only endstop calibration. I to set target precision, J to set probe_radius,​ K to keep current endstop trim settings. ​ In Zgrid module, it starts the grid probing | <​kbd>​G32</​kbd>​ <​kbd>​G32 R</​kbd>​ <​kbd>​G32 E</​kbd>​ <​kbd>​G32 EK</​kbd>​ <​kbd>​G32 I0.02</​kbd>​ |
 | G38.2 G38.3 | Standard probe commands implemented as documented [[http://​linuxcnc.org/​docs/​2.6/​html/​gcode/​gcode.html#​sec:​G38-probe|here]] | <​kbd>'​G38.2 Z-10'</​kbd>​| | G38.2 G38.3 | Standard probe commands implemented as documented [[http://​linuxcnc.org/​docs/​2.6/​html/​gcode/​gcode.html#​sec:​G38-probe|here]] | <​kbd>'​G38.2 Z-10'</​kbd>​|
-| G43.2 | [[http://​smoothieware.org/​motion-control#​adjusting-z-once-printing-starts-sometimes-called-babysteps|Baby steps ]] | G43.2 Z0.05 |+| G43.2 | [[http://​smoothieware.org/​motion-control#​adjusting-z-once-printing-starts-sometimes-called-babysteps|Baby steps ]] | <kbd>G43.2 Z0.05</​kbd> ​|
 | G53 | Must be on a line by itself OR the first G code on a line, the directly following G0/G1 will be executed in MCS coordinates | <​kbd>​G53 G0 X0 Y0</​kbd>​ | | G53 | Must be on a line by itself OR the first G code on a line, the directly following G0/G1 will be executed in MCS coordinates | <​kbd>​G53 G0 X0 Y0</​kbd>​ |
 | [[G54]]-G59.3 | use workspace coordinates http://​linuxcnc.org/​docs/​html/​gcode/​coordinates.html and http://​linuxcnc.org/​docs/​html/​gcode/​g-code.html#​gcode:​g54-g59.3 | <​kbd>​G54</​kbd>​ | | [[G54]]-G59.3 | use workspace coordinates http://​linuxcnc.org/​docs/​html/​gcode/​coordinates.html and http://​linuxcnc.org/​docs/​html/​gcode/​g-code.html#​gcode:​g54-g59.3 | <​kbd>​G54</​kbd>​ |