Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
supported-g-codes [2018/09/26 11:40]
51.6.19.46 [G codes]
supported-g-codes [2018/12/03 17:50] (current)
wolfmanjm [G codes]
Line 20: Line 20:
 | [[G10]] | Do firmware extruder retract | <​kbd>​G10</​kbd>​ | | [[G10]] | Do firmware extruder retract | <​kbd>​G10</​kbd>​ |
 | [[G11]] | Do firmware extruder un-retract | <​kbd>​G11</​kbd>​ | | [[G11]] | Do firmware extruder un-retract | <​kbd>​G11</​kbd>​ |
-| G10 L2 G10 L20 | set workspace coordinates http://​linuxcnc.org/​docs/​html/​gcode/​coordinates.html and http://​linuxcnc.org/​docs/​html/​gcode/​g-code.html#​gcode:​g10-l2| <​kbd>​G10 L2 P1 X0</​kbd>​ |+| G10 L2 G10 L20 | Set workspace coordinates http://​linuxcnc.org/​docs/​html/​gcode/​coordinates.html and http://​linuxcnc.org/​docs/​html/​gcode/​g-code.html#​gcode:​g10-l2| <​kbd>​G10 L2 P1 X0</​kbd>​ |
 | [[G17]] | Select XYZ plane (command is modal)| <​kbd>​G17</​kbd>​ | | [[G17]] | Select XYZ plane (command is modal)| <​kbd>​G17</​kbd>​ |
 | [[G18]] | Select XZY plane (command is modal)| <​kbd>​G18</​kbd>​ | | [[G18]] | Select XZY plane (command is modal)| <​kbd>​G18</​kbd>​ |
Line 31: Line 31:
 | G28.3 | Manual Homing - This allows you to set a home position manually without moving to limit switches | <​kbd>​G28.3</​kbd>​ | | G28.3 | Manual Homing - This allows you to set a home position manually without moving to limit switches | <​kbd>​G28.3</​kbd>​ |
 | G28.4 | Manual Homing based on actuator position- This allows you to set a home position manually based on actuator position (used for rotary delta) | <​kbd>​G28.4</​kbd>​ | | G28.4 | Manual Homing based on actuator position- This allows you to set a home position manually based on actuator position (used for rotary delta) | <​kbd>​G28.4</​kbd>​ |
-| G28.5 | clears ​the homed flag for the specified axis, or all if not specifed | <​kbd>​G28.5</​kbd>​ <​kbd>​G28.5 Z0</​kbd>​ | +| G28.5 | Clears ​the homed flag for the specified axis, or all if not specifed | <​kbd>​G28.5</​kbd>​ <​kbd>​G28.5 Z0</​kbd>​ | 
-| G28.6 | shows the homing status of each axis | <​kbd>​G28.6</​kbd>​ |+| G28.6 | Shows the homing status of each axis | <​kbd>​G28.6</​kbd>​ | 
 +| G29 | Probes the bed and outputs the bed heights depending on levelling strategy selected, see [[ZProbe]] ​ | <​kbd>​G29</​kbd>​ |
 | [[G30]] | Simple Z probe at current XY, reports distance moved down until probe triggers. optional F parameter defines the speed of probing, zprobe.slow_feedrate is used when not supplied | <​kbd>​G30 - G30 F100</​kbd>​ | | [[G30]] | Simple Z probe at current XY, reports distance moved down until probe triggers. optional F parameter defines the speed of probing, zprobe.slow_feedrate is used when not supplied | <​kbd>​G30 - G30 F100</​kbd>​ |
 | G31 | Depends on levelling strategy selected, see [[ZProbe]] ​ | <​kbd>​G31</​kbd>​ | | G31 | Depends on levelling strategy selected, see [[ZProbe]] ​ | <​kbd>​G31</​kbd>​ |
Line 41: Line 42:
 | [[G91]] | Relative mode : passed coordinates will be considered relative to the current point (command is modal)| <​kbd>​G91</​kbd>​ | | [[G91]] | Relative mode : passed coordinates will be considered relative to the current point (command is modal)| <​kbd>​G91</​kbd>​ |
 | [[G92]] | Set global workspace coordinate system to specified coordinates http://​linuxcnc.org/​docs/​html/​gcode/​g-code.html#​gcode:​g92 | <​kbd>​G92 X0 Y0 Z0</​kbd>​ | | [[G92]] | Set global workspace coordinate system to specified coordinates http://​linuxcnc.org/​docs/​html/​gcode/​g-code.html#​gcode:​g92 | <​kbd>​G92 X0 Y0 Z0</​kbd>​ |
-| G92.1 | clear the G92 and G30 Znnn offsets | <​kbd>​G92.1</​kbd>​|+| G92.1 | Clear the G92 and G30 Znnn offsets | <​kbd>​G92.1</​kbd>​|
 |= M-Code |= Description ​  ​|= ​ | |= M-Code |= Description ​  ​|= ​ |
 | [[M3]] | Starts the spindle. Only if spindle module is enabled. The S parameter sets the speed in rotations per minute | <​kbd>​M3 S5000</​kbd>​ | | [[M3]] | Starts the spindle. Only if spindle module is enabled. The S parameter sets the speed in rotations per minute | <​kbd>​M3 S5000</​kbd>​ |
Line 89: Line 90:
 | M205 | X<​junction deviation>​ Z<z junction deviation>​ S<​minimum planner speed>, Z junction deviation only applies to z only moves, 0 disables junction deviation for Z, -1 uses global junction deviation | <​kbd>​M205 X0.05 S30.0</​kbd>​ | | M205 | X<​junction deviation>​ Z<z junction deviation>​ S<​minimum planner speed>, Z junction deviation only applies to z only moves, 0 disables junction deviation for Z, -1 uses global junction deviation | <​kbd>​M205 X0.05 S30.0</​kbd>​ |
 | M206 | Set homing offsets | <​kbd>​M206 X10 Y3 Z0.5</​kbd>​ | | M206 | Set homing offsets | <​kbd>​M206 X10 Y3 Z0.5</​kbd>​ |
-| M207 | set retract length S[[positive|mm]] F[[feedrate|mm/​min]] Z[[additional|zlift/​hop]] Q[[zlift|feedrate mm/min]] | <​kbd>​M207 S4 F30 Z1</​kbd>​ | +| M207 | Set retract length S[[positive|mm]] F[[feedrate|mm/​min]] Z[[additional|zlift/​hop]] Q[[zlift|feedrate mm/min]] | <​kbd>​M207 S4 F30 Z1</​kbd>​ | 
-| M208 | set retract recover length S[[positive|mm surplus to the M207 S*]] F[[feedrate|mm/​min]] | <​kbd>​M208 S0 F8</​kbd>​ |+| M208 | Set retract recover length S[[positive|mm surplus to the M207 S*]] F[[feedrate|mm/​min]] | <​kbd>​M208 S0 F8</​kbd>​ |
 | M220 | S<factor in percent>​- set speed factor override percentage | <​kbd>​M220 S50</​kbd>​ | | M220 | S<factor in percent>​- set speed factor override percentage | <​kbd>​M220 S50</​kbd>​ |
 | M221 | S<flow rate factor in percent>​- set flow rate factor override percentage for current extruder| <​kbd>​M221 S50</​kbd>​ | | M221 | S<flow rate factor in percent>​- set flow rate factor override percentage for current extruder| <​kbd>​M221 S50</​kbd>​ |
Line 107: Line 108:
 | M374 | Z grid strategy: save calibration grid.  optional S parameter saves a custom file with numerical extention | <​kbd>​M374 S123</​kbd>​ | | M374 | Z grid strategy: save calibration grid.  optional S parameter saves a custom file with numerical extention | <​kbd>​M374 S123</​kbd>​ |
 | M375 | Z grid strategy: load calibration grid.  optional S Parameter loads a pre saved custom grid  | <​kbd>​M375 S123</​kbd>​ | | M375 | Z grid strategy: load calibration grid.  optional S Parameter loads a pre saved custom grid  | <​kbd>​M375 S123</​kbd>​ |
 +| M375.1 | display the current grid   | <​kbd>​M375.1</​kbd>​ |
 | M400 | Wait for the queue to be empty before answering "​OK"​ | <​kbd>​M400</​kbd>​ | | M400 | Wait for the queue to be empty before answering "​OK"​ | <​kbd>​M400</​kbd>​ |
 | M407 | Get filament detector information | <​kbd>​M407</​kbd>​ | | M407 | Get filament detector information | <​kbd>​M407</​kbd>​ |
Line 115: Line 117:
 | M504 | Save the settings to an override file with specified extension| <​kbd>​M504 test1</​kbd>​ - saves to config-override.test1 | | M504 | Save the settings to an override file with specified extension| <​kbd>​M504 test1</​kbd>​ - saves to config-override.test1 |
 | M557 | Defines probe points | <​kbd>​M557 P1 X30 Y40.5</​kbd>​ | | M557 | Defines probe points | <​kbd>​M557 P1 X30 Y40.5</​kbd>​ |
-| M561 | clears ​the plane and the bed leveling is disabled until G32 is run again | <​kbd>​M561</​kbd>​ | +| M561 | Clears ​the plane and the bed leveling is disabled until G32 is run again | <​kbd>​M561</​kbd>​ | 
-| M565 | defines ​the probe offsets from the nozzle or tool head | <​kbd>​M565 X3 Y4.5 Z-2.37</​kbd>​ |+| M565 | Defines ​the probe offsets from the nozzle or tool head | <​kbd>​M565 X3 Y4.5 Z-2.37</​kbd>​ |
 | M600 | Suspend print in progress (use M601 to continue) | | | M600 | Suspend print in progress (use M601 to continue) | |
 | M601 | Resume suspended print | | | M601 | Resume suspended print | |
Line 123: Line 125:
 | M670 | ZProbe feedrates Slow/​fast(K)/​Return (mm/sec) max_z (mm) height (mm) | <​kbd>​M670 S5.00 K100.00 R0.00 Z357.55 H5.00</​kbd>​ | | M670 | ZProbe feedrates Slow/​fast(K)/​Return (mm/sec) max_z (mm) height (mm) | <​kbd>​M670 S5.00 K100.00 R0.00 Z357.55 H5.00</​kbd>​ |
 | M906 | Set Current in milliamp for SPI drivers, only if the driver is handled by the motorcontrol module | <​kbd>​M906 A1000 B1100</​kbd>​ | | M906 | Set Current in milliamp for SPI drivers, only if the driver is handled by the motorcontrol module | <​kbd>​M906 A1000 B1100</​kbd>​ |
-| M907 | Set Current control via digipot for each axis (current in amps) | <​kbd>​M907 X1.0 Y1.0 Z1.0 E1.5</​kbd>​ |+| M907 | Set Current control via digipot for each axis (current in amps) | <​kbd>​M907 X1.0 Y1.0 Z1.0 A1.5</​kbd>​ |
 | M909 | Set microsteps (1/n), ONLY for advanced drivers handled by motordriver module, M909.1 will also set the steps/mm accordingly | <​kbd>​M909 A16 B64</​kbd>​ | | M909 | Set microsteps (1/n), ONLY for advanced drivers handled by motordriver module, M909.1 will also set the steps/mm accordingly | <​kbd>​M909 A16 B64</​kbd>​ |
-| M910.x | setup advanced driver chips that support SPI setup, parameters are specific to each chip see chip docs | <​kbd>​M910</​kbd>​ |+| M910.x | Setup advanced driver chips that support SPI setup, parameters are specific to each chip see chip docs | <​kbd>​M910</​kbd>​ |
 | M957 | (with Spindle module enabled) Report the current spindle speed and PWM value | <​kbd>​M957</​kbd>​ | | M957 | (with Spindle module enabled) Report the current spindle speed and PWM value | <​kbd>​M957</​kbd>​ |
 | M958 | (with Spindle module enabled) Report the current spindle PID parameters. <​kbd>​M958 Px.xx Ix.xx Dx.xx</​kbd>​ will set them (to save the new values, you need to edit config file manually). | <​kbd>​M958 P0.1</​kbd>​ | | M958 | (with Spindle module enabled) Report the current spindle PID parameters. <​kbd>​M958 Px.xx Ix.xx Dx.xx</​kbd>​ will set them (to save the new values, you need to edit config file manually). | <​kbd>​M958 P0.1</​kbd>​ |