Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
Next revision Both sides next revision
supported-g-codes [2018/11/16 20:49]
178.148.197.25 M375.1 - display the current grid
supported-g-codes [2018/12/21 12:18]
wolfmanjm [G codes]
Line 109: Line 109:
 | M375 | Z grid strategy: load calibration grid.  optional S Parameter loads a pre saved custom grid  | <​kbd>​M375 S123</​kbd>​ | | M375 | Z grid strategy: load calibration grid.  optional S Parameter loads a pre saved custom grid  | <​kbd>​M375 S123</​kbd>​ |
 | M375.1 | display the current grid   | <​kbd>​M375.1</​kbd>​ | | M375.1 | display the current grid   | <​kbd>​M375.1</​kbd>​ |
-| M400 | Wait for the queue to be empty before ​answering "​OK" ​| <​kbd>​M400</​kbd>​ |+| M400 | Wait for the queue to be empty and the motors to stop before ​the M400 answers ok | <​kbd>​M400</​kbd>​ |
 | M407 | Get filament detector information | <​kbd>​M407</​kbd>​ | | M407 | Get filament detector information | <​kbd>​M407</​kbd>​ |
 | M500 | Save some volatile settings to an override file | <​kbd>​M500</​kbd>​ | | M500 | Save some volatile settings to an override file | <​kbd>​M500</​kbd>​ |
Line 125: Line 125:
 | M670 | ZProbe feedrates Slow/​fast(K)/​Return (mm/sec) max_z (mm) height (mm) | <​kbd>​M670 S5.00 K100.00 R0.00 Z357.55 H5.00</​kbd>​ | | M670 | ZProbe feedrates Slow/​fast(K)/​Return (mm/sec) max_z (mm) height (mm) | <​kbd>​M670 S5.00 K100.00 R0.00 Z357.55 H5.00</​kbd>​ |
 | M906 | Set Current in milliamp for SPI drivers, only if the driver is handled by the motorcontrol module | <​kbd>​M906 A1000 B1100</​kbd>​ | | M906 | Set Current in milliamp for SPI drivers, only if the driver is handled by the motorcontrol module | <​kbd>​M906 A1000 B1100</​kbd>​ |
-| M907 | Set Current control via digipot for each axis (current in amps) | <​kbd>​M907 X1.0 Y1.0 Z1.0 E1.5</​kbd>​ |+| M907 | Set Current control via digipot for each axis (current in amps) | <​kbd>​M907 X1.0 Y1.0 Z1.0 A1.5</​kbd>​ |
 | M909 | Set microsteps (1/n), ONLY for advanced drivers handled by motordriver module, M909.1 will also set the steps/mm accordingly | <​kbd>​M909 A16 B64</​kbd>​ | | M909 | Set microsteps (1/n), ONLY for advanced drivers handled by motordriver module, M909.1 will also set the steps/mm accordingly | <​kbd>​M909 A16 B64</​kbd>​ |
 | M910.x | Setup advanced driver chips that support SPI setup, parameters are specific to each chip see chip docs | <​kbd>​M910</​kbd>​ | | M910.x | Setup advanced driver chips that support SPI setup, parameters are specific to each chip see chip docs | <​kbd>​M910</​kbd>​ |