Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
panel [2017/05/22 02:47]
87.81.12.2 [Custom menu entries]
panel [2019/05/16 01:01] (current)
88.130.96.215 [Viki2 from panacutt.com] link had a typo, added direct link to product in description
Line 65: Line 65:
 custom_menu.filament_change_r.command ​             M24               # custom_menu.filament_change_r.command ​             M24               #
 </​code>​ </​code>​
- 
-Another example BLT probing Commands 
-<​code>​ 
-custom_menu.blt_probe_out.enable ​          ​true ​           # 
-custom_menu.blt_probe_out.name ​            ​BLT_Probe_Out ​  # 
-custom_menu.blt_probe_out.command ​         M280S3 ​         # 
- 
-custom_menu.blt_probe_In.enable ​          ​true ​            # 
-custom_menu.blt_probe_In.name ​            ​BLT_Probe_In ​    # 
-custom_menu.blt_probe_In.command ​         M280S7 ​          # 
- 
-custom_menu.blt_reset_alarm.enable ​       true             # 
-custom_menu.blt_reset_alarm.name ​         BLT_Reset_Alarm ​ # 
-custom_menu.blt_reset_alarm.command ​      ​M280S10.6 ​       # 
- 
-custom_menu.blt_reset_alarm.enable ​       true             # 
-custom_menu.blt_reset_alarm.name ​         BLT_Test_Alarm ​  # 
-custom_menu.blt_reset_Alarm.command ​      ​M280S8.4|G4S15|M280S10.6|M280S7 #Runs Self Test 15secs resets and pulls pin up 
- 
-custom_menu.BLT_probe_bed.enable ​         true                             # 
-custom_menu.BLT_probe_bed.name ​           BLT_Probe_Bed ​                   # 
-custom_menu.BLT_probe_bed.command ​        ​M280_S3.0|G32|M280_S7.0|G1X10Y10 #  
-</​code>​ 
- 
 === External SD card setup === External SD card setup
 <callout type="​danger"​ icon="​true">​ <callout type="​danger"​ icon="​true">​
Line 186: Line 162:
  
 On the back of the GLCD EXP1 is to left and EXP2 is to right, pin 1 is bottom left, pin 2 is top left etc. On the back of the GLCD EXP1 is to left and EXP2 is to right, pin 1 is bottom left, pin 2 is top left etc.
-=5v is EXP1 pin 10, Gnd is EXP1 pin 9+5v is EXP1 pin 10, Gnd is EXP1 pin 9
  
 <​code>​ <​code>​
Line 251: Line 227:
 ~~CLEARFIX~~ ~~CLEARFIX~~
  
-== Viki2 from panacutt.com+== Viki2 from panucatt.com
  
-Viki2 wires to an Azteeg X5 mini with a flat cable as it has 1:1 pin mapping. The ConfigSample for the Azteeg mini has the config settings required, just uncomment them,+[[http://​www.panucatt.com/​product_p/​vikilcd2.htm|Viki2]] wires to an Azteeg X5 mini with a flat cable as it has 1:1 pin mapping. The ConfigSample for the Azteeg mini has the config settings required, just uncomment them,
  
 The config for Azteeg X5 is different to smoothieboard and is shown in the file https://​github.com/​Smoothieware/​Smoothieware/​blob/​2f88d440ee3f79cb5202d242967b555fa35c7423/​ConfigSamples/​AzteegX5Mini/​config#​L178 The config for Azteeg X5 is different to smoothieboard and is shown in the file https://​github.com/​Smoothieware/​Smoothieware/​blob/​2f88d440ee3f79cb5202d242967b555fa35c7423/​ConfigSamples/​AzteegX5Mini/​config#​L178
Line 295: Line 271:
 ENCB to P3.26 ENCB to P3.26
 ENCA to P3.25 ENCA to P3.25
-MISO to P0.8+MISO to P0.17
 A0 to P2.11 A0 to P2.11
 MOSI to P0.18 MOSI to P0.18
Line 342: Line 318:
  
 <​code>​ <​code>​
-3.25<-- encoder ​ A  [2]-|¯¯¯¯¯|-[4] encoder sw -->GND+3.25<-- encoder ​ A  [2]-|¯¯¯¯¯|-[4] encoder sw -->GND
  ​GND<​-- encoder Com [1]-| (O) |  ​GND<​-- encoder Com [1]-| (O) |
 3.26<-- encoder ​ B  [3]-|_____|-[5] encoder sw -->1.30 3.26<-- encoder ​ B  [3]-|_____|-[5] encoder sw -->1.30
Line 386: Line 362:
 See the wiring diagram [[http://​chibidibidiwah.wdfiles.com/​local--files/​panel/​smoothieboard-LCD_1024.jpg|here]]. See the wiring diagram [[http://​chibidibidiwah.wdfiles.com/​local--files/​panel/​smoothieboard-LCD_1024.jpg|here]].
  
-Configuration : +Configuration :
  
 <​code>​ <​code>​
Line 411: Line 387:
 panel.external_sd.sdcd_pin ​         0.28!^ ​          # sd detect signal (set to nc if no sdcard detect) panel.external_sd.sdcd_pin ​         0.28!^ ​          # sd detect signal (set to nc if no sdcard detect)
 </​code>​ </​code>​
 +
 +