Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
new-features [2017/01/25 16:15]
arthur
new-features [2017/01/25 16:21] (current)
arthur
Line 1: Line 1:
 == 2013/04: == 2013/04:
-* Implemented support for[[*https://​github.com/​foosel/​OctoPrint|Octoprint]] host software.+* Implemented support for [[*https://​github.com/​foosel/​OctoPrint|Octoprint]] host software.
  
 == 2013/03: == 2013/03:
-* Added native[[*https://​github.com/​arthurwolf/​Smoothie/​pull/​152/​files|HBot]] support to edge. Set "​arm_solution"​ to "​hbot"​ in your config to enable. +* Added native [[*https://​github.com/​arthurwolf/​Smoothie/​pull/​152/​files|HBot]] support to edge. Set "​arm_solution"​ to "​hbot"​ in your config to enable. 
-* Added[[*https://​github.com/​arthurwolf/​Smoothie/​pull/​142/​files|FirmConfigSource]] to edge. Now src/​config.default gets compiled into the rom and read at each boot. The src/​config.default file uses the same format as a normal sd config file. +* Added [[*https://​github.com/​arthurwolf/​Smoothie/​pull/​142/​files|FirmConfigSource]] to edge. Now src/​config.default gets compiled into the rom and read at each boot. The src/​config.default file uses the same format as a normal sd config file. 
-* Added[[*https://​github.com/​arthurwolf/​Smoothie/​pull/​144/​files|delta_segments_per_second]] to edge. This provides a segmentation based on the current feedrate and speed override, where the number of segments is inversely proportional to feedrate.+* Added [[*https://​github.com/​arthurwolf/​Smoothie/​pull/​144/​files|delta_segments_per_second]] to edge. This provides a segmentation based on the current feedrate and speed override, where the number of segments is inversely proportional to feedrate.
 * The config file on the sd card can now be named either config or config.txt * The config file on the sd card can now be named either config or config.txt
  
 == 2013/02: == 2013/02:
 * reset and dfu commands added to SimpleShell * reset and dfu commands added to SimpleShell
-* Added support for[[*https://​github.com/​arthurwolf/​Smoothie/​pull/​124/​files|onboot.gcode]] to run automatically at power up by setting on_boot_gcode_enable to true in config. The name of the file to be run can also be changed by setting on_boot_gcode. +* Added support for [[*https://​github.com/​arthurwolf/​Smoothie/​pull/​124/​files|onboot.gcode]] to run automatically at power up by setting on_boot_gcode_enable to true in config. The name of the file to be run can also be changed by setting on_boot_gcode. 
-* Added[[*https://​github.com/​arthurwolf/​Smoothie/​pull/​123/​files|button]],​ which in a sense is the other half of the Switch module. This module will trigger custom m-codes when a pin is toggled. The combination of Button and Switch modules allows for '​programming'​ of basic behaviors with only simple config changes. An example would be a physical button that turns a fan, heater, or other tool on and off. +* Added [[*https://​github.com/​arthurwolf/​Smoothie/​pull/​123/​files|button]],​ which in a sense is the other half of the Switch module. This module will trigger custom m-codes when a pin is toggled. The combination of Button and Switch modules allows for '​programming'​ of basic behaviors with only simple config changes. An example would be a physical button that turns a fan, heater, or other tool on and off. 
-* Added[[*https://​github.com/​arthurwolf/​Smoothie/​pull/​121/​files|break]] command to enter debug mode from command line +* Added [[*https://​github.com/​arthurwolf/​Smoothie/​pull/​121/​files|break]] command to enter debug mode from command line 
-* Added[[*https://​github.com/​arthurwolf/​Smoothie/​pull/​115/​files|rotatable_cartesian]] arm solution which allows the print bed to be rotated arbitrarily. Setting this arm solution to 45deg is one way of making an h-bot print straight, but it wouldn'​t have working endstops. +* Added [[*https://​github.com/​arthurwolf/​Smoothie/​pull/​115/​files|rotatable_cartesian]] arm solution which allows the print bed to be rotated arbitrarily. Setting this arm solution to 45deg is one way of making an h-bot print straight, but it wouldn'​t have working endstops. 
-* Added per axis[[*https://​github.com/​arthurwolf/​Smoothie/​pull/​114/​files|homing direction]] config option +* Added per axis [[*https://​github.com/​arthurwolf/​Smoothie/​pull/​114/​files|homing direction]] config option 
-* Added initial[[*https://​github.com/​arthurwolf/​Smoothie/​pull/​110/​files|Rostock]] support!+* Added initial [[*https://​github.com/​arthurwolf/​Smoothie/​pull/​110/​files|Rostock]] support!
 * Now to enable the second usb serial port set second_usb_serial_enable to true in config * Now to enable the second usb serial port set second_usb_serial_enable to true in config
 * Added progress, abort, and help commands to SimpleShell * Added progress, abort, and help commands to SimpleShell