Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
blue-box-guide [2017/01/25 16:12]
arthur
blue-box-guide [2017/01/25 18:54]
arthur
Line 3: Line 3:
 = SmoothK40 Guide = SmoothK40 Guide
  
-[[[image|K40-400-90px]]]+[[image K40-400-90px]]
  
 You want to use proper softwares to drive your Laser machine, this is the best reason to change for a Smoothie board, and start to use your laser cutter as simply as a inkjet printer. You want to use proper softwares to drive your Laser machine, this is the best reason to change for a Smoothie board, and start to use your laser cutter as simply as a inkjet printer.
  
-**__[[[size|larger]]]Smoothie guide for K40[[/​size]]__**+**__[[size larger]]Smoothie guide for K40[[/​size]]__**
 by Stephane BUISSON (Oct/Nov 2015) by Stephane BUISSON (Oct/Nov 2015)
  
Line 13: Line 13:
 it’s different model and type out there and the wiring would vary accordingly. it’s different model and type out there and the wiring would vary accordingly.
  
-[[[image|PSU.jpg]]]+[[image PSU.jpg]]
  
 I will look at  2 common cases: I will look at  2 common cases:
Line 31: Line 31:
 conditions for a recent PSU (not my case) conditions for a recent PSU (not my case)
  
-[[[image|Spreadsheet.tiff]]]+[[image Spreadsheet.tiff]]
  
 Personally I got a MYJG40W from [http://​www.jnmydy.com] and I can’t find any manual for it. (don’t speak Chinese) Personally I got a MYJG40W from [http://​www.jnmydy.com] and I can’t find any manual for it. (don’t speak Chinese)
Line 37: Line 37:
 but I make it work with this schema : but I make it work with this schema :
  
-[[[image|k40SmoothieWiring4.png]]]+[[image k40SmoothieWiring4.png]]
  
 Connecting end stops and motors : Connecting end stops and motors :
Line 43: Line 43:
 from factory I identify 2 original wirings, very similar. flat connector (CN3) or cables (CN21 CN22 CN4) doing the same thing. from factory I identify 2 original wirings, very similar. flat connector (CN3) or cables (CN21 CN22 CN4) doing the same thing.
  
-[[[image|PastedGraphic.tiff]]]+[[image PastedGraphic.tiff]]
  
 You need to play with a controller to find out your wiring on flat cable. You need to play with a controller to find out your wiring on flat cable.
Line 58: Line 58:
 see schema for wiring. see schema for wiring.
  
-[[[image|Smoothieattempt.jpg]]]+[[image Smoothieattempt.jpg]]
  
 === LCD === LCD
Line 72: Line 72:
 [http://​www.smoothmotor.com/​Standard-Models/​Nema-Stepper-Motor.html] [http://​www.smoothmotor.com/​Standard-Models/​Nema-Stepper-Motor.html]
  
-[[[image|page8image31312.jpg]]]+[[image page8image31312.jpg]]
 X Motor (double sided shaft) 17HA507H-22P3 X Motor (double sided shaft) 17HA507H-22P3
-[[[image|page9image400.jpg]]]+[[image page9image400.jpg]]
 Y Motor 17HA113Y-22A2 FH140513 Y Motor 17HA113Y-22A2 FH140513
  
Line 102: Line 102:
 â€¦. â€¦.
  
-[[code]]+<code>
 # Arm solution configuration : Cartesian robot. Translates mm positions into stepper positions # Arm solution configuration : Cartesian robot. Translates mm positions into stepper positions
 alpha_steps_per_mm ​                          ​157.575 ​              # Steps per mm for alpha stepper (based on my measurements) alpha_steps_per_mm ​                          ​157.575 ​              # Steps per mm for alpha stepper (based on my measurements)
 beta_steps_per_mm ​                           157.575 ​              # Steps per mm for beta stepper beta_steps_per_mm ​                           157.575 ​              # Steps per mm for beta stepper
 gamma_steps_per_mm ​                          ​1600 ​            # Steps per mm for gamma stepper gamma_steps_per_mm ​                          ​1600 ​            # Steps per mm for gamma stepper
-[[/code]]+</code>
  
 â€¦. â€¦.
  
-[[code]]+<code>
 # Stepper module pins ( ports, and pin numbers, appending "​!"​ to the number will invert a pin ) # Stepper module pins ( ports, and pin numbers, appending "​!"​ to the number will invert a pin )
 alpha_step_pin ​                              ​2.0 ​             # Pin for alpha stepper step signal alpha_step_pin ​                              ​2.0 ​             # Pin for alpha stepper step signal
Line 124: Line 124:
 beta_current ​                                ​0.5 ​             # Y stepper motor current beta_current ​                                ​0.5 ​             # Y stepper motor current
 beta_max_rate ​                               30000.0 ​         # mm/min beta_max_rate ​                               30000.0 ​         # mm/min
-[[/code]]+</code>
  
 .... ....
  
-[[code]]+<code>
 # Laser module configuration # Laser module configuration
 laser_module_enable ​                         true            # Whether to activate the laser module at all. All configuration is laser_module_enable ​                         true            # Whether to activate the laser module at all. All configuration is
Line 138: Line 138:
                                                               # active without actually burning                                                               # active without actually burning
 laser_module_pwm_period ​                     20              # this sets the pwm frequency as the period in microseconds laser_module_pwm_period ​                     20              # this sets the pwm frequency as the period in microseconds
-[[/code]]+</code>
  
 â€¦. â€¦.
  
-[[code]]+<code>
 # network settings # network settings
 network.enable ​                              ​true ​           # enable the ethernet network services network.enable ​                              ​true ​           # enable the ethernet network services
Line 154: Line 154:
 #​network.ip_gateway ​                          ​192.168.3.1 ​     # the gateway address #​network.ip_gateway ​                          ​192.168.3.1 ​     # the gateway address
 #​network.mac_override ​                        ​xx.xx.xx.xx.xx.xx ​ # override the mac address, only do this if you have a conflict #​network.mac_override ​                        ​xx.xx.xx.xx.xx.xx ​ # override the mac address, only do this if you have a conflict
-[[/code]]+</code>
  
-[[[image|WELCOME2SMOOTHIE.tiff]]]+[[image WELCOME2SMOOTHIE.tiff]]
  
 Command: tracing (G1) a line from your actual position to (X100, Y100) full laser power (S1) Command: tracing (G1) a line from your actual position to (X100, Y100) full laser power (S1)
Line 168: Line 168:
 Select menu Option, manage laser cutter, choose smoothie, fill your settings in. you are done ;-)) Select menu Option, manage laser cutter, choose smoothie, fill your settings in. you are done ;-))
  
-[[[image|VisicutSettings.jpg]]]+[[image VisicutSettings.jpg]]
  
 == Fusion 360 == Fusion 360